DIGITAL MULTIMETER KYORITSU KEWMATE 2012RA JAPAN

Manufacturer: TES
Model: TES-2620
Original: Taiwan

-3 3/4 Digital LCD with Bar-graph
-Water-Proof ABS housing
-Auto-power off
-Auto ranging
-ADP range to accommodate
-Current, Temp., Humidity adaptor
-Current: (AC/DC)4m/40m/400m/20A
-Voltage: (AC/DC) (±0.5% rdg ±1 dgt) 400m/4/40/400/750V (AC)/1000V (DC)
-Resistance: 400/4K/40K/400K/4M/40MΩ
-Frequency: 100/1K/10K/100K/500K Hz

Manufacturer: TES
Model: TES-2700
Original: Taiwan

-Autoranging and Auto-power-off
-3200 count LCD analog bar-graph
-Data-hold mode available at ohms
-Overload protection up to 600 Vrms
-Current: 320u/3.2m/32m/320m/20A
-Voltage: (AC/DC) (±0.5% rdg ±2 dgt)
320m/3.2/32/600V (DC)
3.2/32/320/600V (AC)
-Resistance:320/3.2K/32K/320K/3.2M/30MΩ

Manufacturer: TES
Model: TES-2732A
Original: Taiwan

-DMM talks with PC via RS-232 interface
-Data logger function (4,808 readings)
-Direct input of V, A, Ohm, Hz, Cx&°C/°Fwithout any further signal modification
-Current: (AC/DC) 200u/2m/20m/200m/20A (AC/DC)
-Voltage: (AC/DC) (±0.5% rdg ±1 dgt)
-200m/2/20/200/600V (DC)/600V (AC)
-Frequency: (±0.5% rdg ±2 dgts); 10Hz~20M Hz (Auto range)
-Resistance: 200/2K/20K/200K/2M/20MΩ
-Capacitance: 2000P/200n/2µF/20µF

Manufacturer: TES
Model: Prova 700
Original: Taiwan

-Max. Test Current: 5A
-Four Terminal Kelvin measurement.
-Best resolution 1 µΩ .
-Basic accuracy 0.25%.
-Manual or Auto Range.
-Measurement of resistive and inductive materials.
-Readings Hold function.
-Cable length measurement
-Large LCD (5-digit) with backlight
-Low battery (voltage) alarm.
-Low Power consumption
-Rechargeable lithium batteries and AC adaptor
-RS232C (to USB bridge) cable
-Built-in calendar clock
-Built-in batteries charging circuit
Application
-Coil resistance of Electric motor
-Contact resistance of Switch and Relay
-Resistance of Bus bar, Breaker, Fuse, Inductance and Shunt

• Variable frequency drive (VFD) V & Hz measurement.
• Lo Z voltage measurement to drain ghost voltages.
• Check 30 phase sequence.
• Voltage harmonic ratio measurement.
Smart ohm for ground resistance measurement.
. Data hold & Auto hold mode.
• Max/Min/Avg record mode.
• Backlight LCD display
• Relative value display.
• Frequecy count. (Auto-Range)
• Temperature type K, J measurement.
• Capacitance measurement.
Data memory & read function.

• True RMS can measure and indicate distorted waveforms
• 6040 counts with Bar Graph display
• MIN/MAX function enables to record min & max value
• REL(relative value) function to indicate the measurement variation

High Accuracy, High Performance and Reliable Measurements
• 0.09% basic DC accuracy
• Large display with 6,000 counts
• True-RMS Measurements
• Low-pass filter for motor drive measurements
• User calibration function

Safety design for industrial use
• Complies with IEC 61010-1 CAT IV 600V , CAT III 1000V
• Terminal shutter to prevent incorrect test leads' insertion in current terminals
• Very wide operating temperature range from -10 to 55ºC

• Elegant and easy-to-use cabinet
• Large display with 6000 counts and Backlight
• Enhanced current measuring function using an external clamp sensor
• Two detachable holders, flat and wing type
• Accurate reading with True RMS
• Safety Standard IEC 61010-1 CAT IV 300V / CAT III 600V

Manufacturer: TES
Model: Prova 710
Original: Taiwan

-Max. Test Current: 10A
-Four Terminal Kelvin measurement.
-Best resolution 1 µΩ .
-Basic accuracy 0.25%.
-Manual or Auto Range.
-Measurement of resistive and inductive materials.
-Readings Hold function.
-Cable length measurement
-Large LCD (5-digit) with backlight
-Low battery (voltage) alarm.
-Low Power consumption
-Rechargeable lithium batteries and AC adaptor
-RS232C (to USB bridge) cable
-Built-in calendar clock
-Built-in batteries charging circuit
Application
-Coil resistance of Electric motor
-Contact resistance of Switch and Relay
-Resistance of Bus bar, Breaker, Fuse, Inductance and Shunt

• Display : 4000 counts.
• Auto range and manual range selector provided.
(with range hold feature)
• Resistance range provides audible continuity test.
• Automatically turns power off in about 30 minutes to conserve battery life.
• Direct current measurement up to 10A AC and DC.
• With Holster.

• Compact in Size, Light in Weight and Simple in Use.
• Double moulding provides comfortable and good feeling in hand.
• Penlight illuminates brightly the point to be measured, even in dark place.
• Backlight LCD is highly visible, even in darkness.
• Unique wrapping mechanism for test lead in the rear side compartment.
• Unique protection mechanism for the test prod for safety.
• All ranges including Ohm range are protected against overload voltage of 600V.

• Capable of measuring AC and DC currents up to 100A with OPEN CLAMP SENSOR.
• 3400 counts with bargraph display.
• Pocket size and heavy duty design.

• 1000A AC Clamp Meter, AC60/600/1000A Auto Range
• True-RMS
• Peak Hold for inrush current
• 6000 counts display with Backlight
• ø33mm Tear Drop shaped jaw easy to use in tight places
• Double molding gives comfortable feeling
• Safety standerd IEC 61010-1, CAT Ⅳ 300V/ CAT Ⅲ 600V

High Accuracy, High Performance and Reliable Measurements
• 0.02% basic DC accuracy
• Large display with 50,000 counts
• Dual display for double indication for AC and DC, V and Hz, etc.
• True-RMS Measurements AC and AC+DC
• Wide AC Frequency bandwidth from 10Hz to 100kHz
• True-RMS or MEAN value detection mode can be selected
• Fast Peak Hold response time of 250µs
• Low-pass filter for motor drive measurements
• Low Power Ω for resistance measurements on sensible electronic circuits by a low and safe test current
• User calibration function

Safety design for industrial use
• Complies with IEC 61010-1 CAT IV 600V, CAT III 1000V
• Terminal shutter to prevent incorrect test leads' insertion in current terminals
• Very wide operating temperature range from -20 to 55ºC

Reliable support for data management
• Large data internal memory
KEW 1062: 10,000 data (logging), 100 data (manual)
• Download data and Live Monitoring on a PC via the USB interface
(Option for USB Communication set)
* MAX 32,767 data can be transferred.

• AC and DC voltage tests up to 690V with LEDs and LCD
• Comply with the latest standards IEC 61243 and IEC 61010
• Novel design
Large and bright LEDs: Values are visible in the dark place
Ergonomic design fits in the hand
• Two functions are available in one model
"Measurement without battery" and "Self Test (all LED on)"
• Test leads withstand harsh environments at low temperature
• Penlight (white LED)
• Auto-power ON/OFF
• Audible indication
• Variable test tips, φ2mm or φ4mm
• Probe protection cover can store the attachment of caps
• IP65 (IEC 60529)

Auto-power off 3-3/4 digit, 4000 count DMM with Peak Hold
Frequency Count (Auto-Ranging)
Inductance, Capacitance and Temperature (diode type) checks
 

Protect life and property from faulty appliances

・Battery operated
・PASS / FAIL result
・Color status back light
・10 mA & 30 mA RCD test(Isolation transformer built in)
　Memory function up to 999 data
・Printer output
・Complies to AS / NZS 3760

KEW 6205 equipped with Wireless LAN is available only
in Australia and New Zealand.

• Elegant shiny-black finish
• Comes with user-friendly Hard case
• Large Display
• Accurate reading with True-RMS technology
• Electronic protection (no fuse!) on ohm and continuity ranges
• Safety Standard IEC 61010-1 / 61010-031 / 61010-2-033 CAT III 300V / CAT II 600V

• AC and DC voltage tests up to 690V with LED
• Comply with the latest standards IEC 61243 and IEC 61010
• Novel design
Large and bright LEDs: Values are visible in the dark place
Ergonomic design fits in the hand
• Two functions are available in one model
"Measurement without battery" and "Self Test (all LED on)"
• Test leads withstand harsh environments at low temperature
• Penlight (white LED)
• Auto-power ON/OFF
• Audible indication
• Variable test tips, φ2mm or φ4mm
• Probe protection cover can store the attachment of caps
• IP65 (IEC 60529)